In order to speed up the economic benefits of mutton sheep breeding and reduce the labor intensity of the majority of farmers, the use of semi-shed plastic heating is one of the measures that must be taken in mutton sheep breeding. First, the benefits of using a warm circle of sheep 1, the temperature is appropriate, to protect the fetus. The main reason for winter sheep dropping out is the lack of cold and nutrition. In winter, as the sheep's body resists cold and strong winds, the heat output of the sheep body will increase significantly. This requires a lot of fat in the body to maintain body temperature balance, resulting in the sheep being quickly thin. 2, improve the survival rate of young livestock. The warm circle can form a good microclimate under bad weather conditions. In this environment, raising mutton sheep can make the ewes strong and milky. The winter lambs will not freeze because of cold, nor will they cause indigestion and colds due to the cold. 3, can promote the normal growth and development of young animals. Because the temperature of the warm circle can be maintained below minus 5°C and near the critical temperature, less energy is consumed to maintain the body temperature, and the thermal energy absorbed by the body can ensure the normal growth and development of winter lambs. 4, warm circle temperature is appropriate. The proper temperature of the warm circle makes it possible for mutton sheep not to be piled or smashed in the cold at night, thus eliminating the economic losses caused by freezing and pressing and ensuring the smooth proceeding of winter lambs. There is no special overnight staff when picking lambs, which greatly reduces the labor intensity of farmers. Second, the construction of plastic greenhouses 1, the choice of the site. Should be selected in the high dry terrain, to prevent water backflow, drainage should be smooth. At the same time, it is necessary to take into consideration the prevention of epidemics, convenient transportation, adequate water supply, good water quality, avoidance of tuyere and other undesirable factors. 2, heading. In order to make full use of solar energy, the building should face north and south, and the southeast or west side should not exceed 15°C. If the sheep house needs to be oriented north-south, the roof of the house can be a full-arched plastic shed with a corridor in the middle and double arrangement in the left and right. The front of the sheep house does not have a tall building within a certain distance, so it is advisable to not affect the lighting. 3, a reasonable set of ventilation openings. The vent of the greenhouse should be located on the leeward side of the roof. The small sheep houses used by farmers can use round or square exhaust outlets. Each exhaust outlet is about 0.05 square meters in size, and it is generally set every 3 meters. The top of the exhaust port should be equipped with a windproof cap to prevent rainwater from entering. 4. The plastic film slope of the shed. The slope of the plastic film refers to the angle between the plastic film and the ground plane. Should be controlled between 40-55, so you can get a higher lighting rate. 5, determine the size of the greenhouse. Generally based on the number of sheep, the general lamb covers an area of ​​0.75-1/only, and the adult sheep occupies 1-1.5?/only. If the General Assembly raises the cost of heating sheds and affects the temperature in the sheds, too small will cause the sheep to become crowded, raise the temperature inside the shed, and make the air circulate. In order for the greenhouse to achieve the desired lighting effect, the shape of the circle must be rectangular. The width of the circle cannot be changed at will, and the length can be changed as needed. The ridge height has a great relationship with the lighting effect, and it cannot change the ridge height freely, otherwise it will affect the lighting effect or cause waste. Pain Relief Patch For Neck Shoulder,Lower Back And Leg
Pain Relief Patch for neck shoulder, lower back and leg.
Pain Relief Patch,Pain Relief Pad,Pain Relief Plaster,Neck Pain Relief Patch,Back Pain Relief Pacth Shandong XiJieYiTong International Trade Co.,Ltd. , https://www.xjytmedical.com
[Name] Medical Cold Patch
[Package Dimension] 10cm×12cm 2pieces/box
The pain relief patch is composed of three layers, namely, backing lining, middle gel and protective film. It is free from pharmacological, immunological or metabolic ingredients.
[Scope of Application] For cold physiotherapy, closed soft tissue only.
[Indications]
The patches give fast acting pain relief for strains, sprains, cramp, bruises, swollen areas or joint stiffness.
[How To Use a Patch]
Tear off the packaging bag and remove the patch. Remove the protective film and apply the patch on the skin. One piece, one time. The curing effect of each piece can last for 8-12 hours.
[Attention]
Do not apply the patch on the problematic skin, such as wounds, eczema, dermatitis,or in the eyes. People allergic to herbs and the pregnant are advised not to use the medication. If swelling or irritation occurs, please stop using and if any of these effects persist or worsen.notify your doctor or pharmacist promptly. Children using the patch must be supervised by adults.
[Storage Conditions]
Store below 30c in a dry place away from heat and direct sunlight.