Small electric tablet press operating specifications

Introduction to small electric tablet press:
The small electric tablet press presses various granular raw materials into pellets, which is suitable for laboratory trial production or small batch production of various tablets, sugar tablets, calcium tablets and the like. It is a small bench-top electric (manual) continuous tableting machine. The machine is equipped with a die, the filling depth of the material and the thickness of the tablet can be adjusted.
Small electric tablet press technical parameters:
Die number: 1 pay
Zui large tablet pressure: 15Kn
Zui large tablet diameter: Ï†12mm
Zui large tablet thickness: Ï†6mm
Production capacity: 3500-4000 pieces / h
Electric machine: 550w, 1400 rpm, 220V
Dimensions: 580 Ã— 450 Ã— 625mm
Host weight: 85kg
Small electric tablet press instructions:
First, use and characteristics
TDP-1.5 small electric tablet press can press the granular material into tablets, which can be widely used in pharmaceutical factories, chemical plants, hospitals, scientific research units, laboratory trial production and small batch production.
The machine has excellent performance, strong adaptability, convenient use, easy maintenance, small size, light weight, and can also be shaken when there is no electricity. This machine only installs a die, the filling depth of the material, the thickness of the tablet can be adjusted, can adapt to the requirements of the pharmaceutical industry to suppress various Chinese and Western medicine preparations and other industries to suppress the requirements of various similar products, and is widely accepted by users in various industries. Welcome.
Second, the tablet press installation and wiring
1. The tablet press is mounted on a solid wooden workbench (also mounted on a concrete platform) with three M12 anchor screws. The height of the work surface to the ground is about 600 mm (hand-operated, easy to operate). In order to facilitate the disassembly and repair, the position piece corresponding to the lower punching rod on the wooden workbench should also have a hole of about 35 mm in diameter.
2. Connect the motor to the ground wire before turning on the motor power to ensure safety. Remove the V-belt, turn on the motor power, and start the motor to see if the motor rotates in the correct direction (the direction of rotation of the motor shaft should be opposite to the direction of the arrow on the shield or handwheel). If the direction of rotation is wrong, connect the cable separately and then the V-belt. Installed.
Third, the loading and unloading of the die and the adjustment during tableting
1 , the installation of the die
(1) Install the upper punch: loosen the lower punching fixing screw, turn the handwheel to raise the lower punching rod to the high position of the zui, and insert the lower punch into the hole of the lower punching rod (note that the notched slope of the lower punch is aligned with the lower punch) Tighten the screws and insert them into the bottom. Then tighten the lower fixing screws.
(2) Install the lower punch: Loosen the upper punching tightening nut, insert the upper punching rod into the hole of the upper punching rod, insert it to the end, use a wrench to clamp the hexagonal part of the upper part of the punching rod, and tighten the upper punching tightening nut.
(3) Install the middle mold: Loosen the middle mold fixing screw, put the middle mold into the hole of the middle mold plate, and make the lower punch into the hole of the middle mold, press the bottom and then tighten the middle mold fixing screw. When placing the mold, pay attention to flatten the middle mold to avoid jamming when the skew is placed and damage the hole wall.
(4) Turn the handwheel by hand to slowly lower the upper punch into the middle die hole to observe whether there is collision or friction. If there is collision or friction, loosen the middle die plate fixing screws (two) and adjust the middle die table. The fixed position of the board allows the upper punch to enter
In the middle die hole, tighten the middle die plate fixing screw, and adjust it until the upper punch enters the middle die without collision or friction for the installation.
2 , the adjustment of the film
Turn the handwheel to raise the lower punch to the high position of the zui, and observe whether the lower punch surface is aligned with the plane of the middle mold (or the high or low will affect the output). If not, loosen the butterfly screw and loosen the gear press plate. Move the gear so that the lower punch surface is aligned with the plane of the middle die, then press the platen up and tighten the thumb screw.
At this point, the handwheel is shaken by hand, and the empty car runs for more than ten revolutions. If the machine is running normally, the pressure can be fed and the next step can be adjusted.
3 , the adjustment of the filling depth (ie the adjustment of the weight of the tablet)
Loosen the thumb screw and loosen the gear platen. Turn the lower adjustment gear to the left to raise the lower punch, and the filling depth is reduced (the weight of the tablet is reduced). After adjusting, press the gear press plate up and tighten the butterfly screw.
4 , the adjustment of the pressure (that is, the adjustment of the hardness of the tablet)
Loosen the connecting rod lock nut, turn the upper punching rod, turn to the left to move the upper punching rod downward, the pressure will increase, and the hardness of the pressed tablet will increase; otherwise, the pressure will decrease when the right turn, the hardness of the tablet will decrease. After adjusting, use a wrench to clamp the hexagonal part of the lower part of the punching rod, and still lock the connecting rod lock nut.
At this point, the adjustment of the die is basically completed, and then the motor is tested for more than ten pieces, and the weight of the piece is checked, and the quality such as hardness and surface finish are qualified, and the production can be started. In the production process, the quality of the tablets must be checked at any time and adjusted in time.
5 , the removal of the die
(1) Disassemble the upper punch: Unscrew the upper punching nut to pull out the upper punch. If the fit is tight, use the pliers to clamp the upper punch to pull it out, but be careful not to damage the punch edge.
(2) Disassemble the middle mold: Loosen the middle mold fixing screw, unscrew the lower punch to fix the screw, loosen the butterfly screw, and loosen the gear pressure plate. The transfer adjustment gear is used to raise the lower core rod by 10 millimeters, and the hand wheel is gently rotated, so that the lower punch core rod pushes out the middle mold part, and the middle mold is taken out by hand, if the middle mold fits closely in the hole, Do not use force to turn the hard top of the handwheel to avoid damage to the machine. At this time, the middle die plate must be removed and the middle mold removed.
(3) Disassemble the undershoot: first unscrew the lower punching set screw, then turn the handwheel to raise the lower punching rod to the high position of the zui, then the upper punch can be pulled out by hand. If it is tightly fitted, it can be pinched out with a pliers (be careful not to damage the punch edge).
(4) After the die is disassembled, the adjusting gear must be rotated to make the lower punching rod retreat about 10 mm. When the handwheel is turned to raise the lower punching rod to the high position of the zui, the top end is not higher than the bottom surface of the middle die plate. Do not ignore this step, so as to avoid the accident of the under impact of the core rod and the middle mold when it is used again. After the zui, the undercut fixing screw is still screwed on.
Â
Fourth, the removal and installation of the main parts
1. Disassembly of the middle die plate: Pull out the powder retaining plate, remove the hopper, unscrew the feeder set screw, unscrew the feeder fixing stud and spring, remove the feeder, and unscrew the middle die plate set screw and spring The gasket can be used to remove the middle platen. Installation: Refer to the reverse order above. Pay attention to alignment when screwing the feeder tightening screw. So as not to damage the wire hole of the feeder.
2 , the upper punch core disassembly: loosen the connecting rod lock nut, turn the upper punch rod to disengage from the connecting rod, turn the hand wheel to raise the eccentric wheel shell to the high position of the zui, turn the eccentric shell to make the connecting rod swing to The upper punching rod can be pulled out from the upper side of the mold frame hole. Installation is performed in the reverse order described above.
3. Disassembly of the lower punching rod: Unscrew the lower punching fixing screw, the butterfly screw and the gear pressing plate rotate the adjusting gear, so that the lower punching core rod is lowered and taken out from the bottom hole of the fuselage. Installation: Refer to the reverse order above.
4. Disassembly of the connecting rod: first remove the upper punching rod, then remove the wire retaining ring on the connecting rod pin, take out the connecting rod pin, and then remove the connecting rod. Installation: Follow the reverse order above.
5 , large pulley, pinion and bridge axle disassembly: lower the V-belt, unscrew the right end of the bridge shaft and the washer (in the fuselage), hold the large pulley together with the pinion and the bridge shaft Then, the bridge shaft can be pulled out of the wheel hole. (The large pulley is integrated with the pinion and the bushing, and generally does not need to be disassembled). Installation: Refer to the reverse order above.
6. Spindle disassembly: The disassembly of the spindle should be carried out by two people. First remove the large pulley, then unscrew the nut to remove the lever and lever
Shaft and filling roller. (Remove the handwheel and camshaft if necessary) Remove the protective cover, unscrew the screws and washers, and use a wooden hammer to hit the non-working surface inside the large gear (not significant). Remove it (be careful not to lose the lifting roller), then hit the shaft end with a wooden hammer and a copper rod (be careful not to damage the shaft end screw hole), while holding the other end of the shaft and holding the eccentric wheel shell, slowly The spindle is removed. Installation: Refer to the reverse order above.
5. Lubrication and maintenance of the machine
1. Lubrication of the friction surfaces of all moving parts is an important part of ensuring the normal operation of the machine and prolonging the service life. In particular, if the main moving parts are dry and run in the absence of oil, they will be quickly damaged and cannot be used. Therefore, the tablet press is Before use, all oil cups, oil holes and friction surfaces must be lubricated, and the air is running so that the friction surfaces are covered with oil film before they can be put into use. In the future, each shift will be refueled on time, but it should not be too much for each refueling, so as to avoid spillage affecting cleaning and staining the tablets. The fueling parts and the number of fueling are shown in the following table:
2 , before each shift must check whether the screws are loose, should also pay attention to check during the work process, if loose, immediately tighten, so as to avoid malfunction. The main parts are: upper punch fastening nut, middle die fixing screw, undershoot fixing screw; connecting rod lock nut, link pin set screw; lift fork lock nut (2) butterfly screw; Set fixing screws (2 pieces)
Refueling part and refueling times
Serial number
Refueling part
Lubricating oil
Number of refueling per shift
1
Spindle hole oil cup (2 pieces)
butter
2-3 times
2
Eccentric wheel shell oil cup 1
butter
2-3 times
3
1 bridge axle oil cup
butter
2-3 times
4
Lifting the cam groove (ie the groove inside the large gear)
butter
Every week, check the surface of the groove to wipe off the dirt and add butter once.
5
Filling the groove of the cam
butter
Every shift inspection, depending on the situation
6
Gear tooth surface
butter
Every shift inspection, depending on the situation
7
Oil hole on connecting rod
Motor oil
1 time
8
Swing pivot point of the lever
Motor oil
1 time
9
Upper punching rod surface
Motor oil
2 times
10
Lifting rod surface
Motor oil
2 times
3 , before and after each shift, you must manually test a few pieces, and then turn on the electric tablet after no problem.
4. In the process of tableting, the quality of the die should be checked frequently. If there is a missing edge, crack, or serious damage, it should be replaced in time to avoid damage to the machine and affect the quality of the tablet.
5 , after the use of each day should be taken out of the remaining particles, wipe the various parts of the machine. If the deactivation time is long, the die must be removed and the machine rubbed each side. Wipe the work surface, apply anti-rust oil, cover the dust-proof clothes; the die should be wiped clean and immersed in oil to save.
6. Check the machine regularly, twice a month.
Six, the use of precautions
1. Read the instructions carefully before using the machine for the first time before using it.
2 , the machine can only be operated in a certain direction (see the arrow on the handwheel or the protective cover), can not be reversed, so as not to damage the machine. Pay special attention to the adjustment of the tablet, do not neglect.
3 , belt elastic adjustment: through the two adjustment nut on the electromechanical bottom plate to adjust. Pay attention to the lock after adjustment.
4. When the power is applied without power supply, the V-belt should be removed to reduce the resistance and wear. But don't remove the big pulley, because the large pulley has the effect of the flywheel.
5 , when the electric tablet is pressed, the rotating handle on the hand wheel must be pulled down to avoid injury when running.
6. Regardless of manual or electric compression, the upper punch rod should be in the raised position and then restarted before starting. If in
When the upper punching piece is started in the lowered position, the medium-molded piece is entered just after starting, and at this time, since the rotation speed of the machine has not risen and the inertia is small, the situation of the top car is likely to occur. (That is, after the upper punch enters the middle mold, it is "top dead" due to the resistance of the tablet, so that the machine stops running. When the top car is loaded, the machine is often damaged or the motor is damaged.)
7 , after the car treatment
Â (1) When the car is in the process of electric pressing, the power should be turned off immediately to avoid burning the motor.
Â (2) When the top car is light, you can use the hand to turn the handwheel to make the upper punch pass the "dead point" (but not reversed, so that the feeder does not repeat the feeding, resulting in a more serious top car).
Â (3) When the vehicle is in serious position, loosen the connecting rod lock nut, turn the upper punch rod to raise it to reduce the pressure, and then turn the hand wheel to push the medicine out. Then re-adjust the hardness of the tablets.
8. Always check the quality of the tablets (sheet weight, hardness, surface finish, etc.) during the tableting process, and adjust them in time.
9. The batching granulation process before tableting has a great influence on the tableting. For example, the formulation of granules such as medicines and slips, fillers, binders, etc. (the condition of the powder, the tightness of the granules, the proportion of the granules, the water content, etc.) directly affect the tablets.
the amount. And often due to improper granulation of ingredients, it is impossible to form a piece or even damage the machine. Therefore, the machine cannot be used for tableting semi-solid or moist or non-granular fine powder. In the use, if the pressure has been adjusted to be quite large, it is still not pressed into pieces or pressed into pieces but appears too loose, layering, debris, pitting, falling powder and so on. It is necessary to find out the reasons and solve them from the aspects of ingredients. Do not blindly adjust to increase the pressure, and even damage the machine. In addition, although the hardness of the tablets extruded by some medicines is not large, it has a certain degree of toughness, and it is not bad for it to fall into the ground (usually it can be broken from the height of 1-1.2 meters on the ground), so it should be To meet the requirements of transportation and storage, do not focus on hardness alone, so as to avoid excessive pressure on the tablet and damage the machine.
Seven, common faults
Serial number
category
Fault conditions
The cause of the failure
Failure prevention and treatment
1
Top car
After rushing into the middle mold, "top dead", the machine stops running
(1) The pressure is too large; the tablets are too hard
(2) repeated feeding
(3) The eccentric wheel shell and the spindle hole lack oil, the rotation resistance is too large, and even the phenomenon of â€œbite deathâ€ occurs due to severe wear.
(4) The belt is too loose
(5) Improper starting position
(6) The hand is not strong enough
(1) Adjust the pressure gradually. Do not adjust too much at one time, and the tablets can't be pressed too hard. (2) Avoid repeated feeding. See No. 7 (3). Always keep lubricating. If it has been seriously worn or â€œkilledâ€, it must be disassembled and repaired immediately. (4) Adjust the belt, see the precautions for use, Article 3, (5) See the precautions for use, Article 6. (6) When the hand presser is pressed or the upper punch passes the low point of Zui, it must be more forceful. (7) For the disposal method after the top car, see Article 7 of the precautions for use.
2
Not working well
Generally not working properly
The friction surface of the moving parts lacks oil, enters dirt, rusts, and seriously wears out the parts.
Always check each part to keep it clean and lubricated (see lubrication maintenance section 1). If there is any bad condition, repair it immediately, and do not deteriorate or damage the machine.
Heavy or blocked when the undershoot rises
(1) Since the surface of the die is not light or worn; or due to improper granulation of the ingredients, the powder adheres to the surface of the punch and the middle mold, which increases the resistance of the sheet. (2) The lifting cam is seriously worn or enters the sundries (3) improperly adjusted, so that the lower punching rod rises and the middle mold is ground.
(1) If the die is found to have a sticking phenomenon, replace the die or reprocess the drug according to the situation.
(2) Check and repair, keep it clean and lubricated.
(3) Pay attention to adjustments
3
vibration
Abnormal vibration
(1) Loose parts and screws
(2) The parts are seriously worn
(3) The friction surface is dry or lacks oil or enters the dirt
(1) Regular inspection, see section 2 of lubrication maintenance, (2) frequent inspections, timely repair of worn parts. (3) Always pay attention to the cleaning and lubrication of each friction surface, especially pay attention to the direct view, but the working load is the important friction surface of the main shaft and the eccentric.
4
Wear
The friction surface of the main shaft and the hole is quickly worn or even burned out.
Lack of oil, enter impurities
Always keep clean and lubricated, the lubricant used must be clean and free of impurities
Rapid wear and tear on the bridge axle and sleeve
Ibid.
Ibid.
Upper punching rod and sleeve wear and wear quickly
Ibid.
Ibid.
Lifting cam groove wears quickly
In addition to the above reasons, there are: (1) improper granulation of the ingredients, or the surface of the die is not light, the sticking phenomenon occurs, the sheet resistance is increased and the load of the cam groove is increased, and the wear is rapidly worn. (2) The lifting roller is turned too tight or rusted. Do not move.
(1) Check the die. If there is a sticking phenomenon, replace the die or re-dosing and granulating according to the situation.
(2) Remove and repair
Die surface wears quickly
(1) Improper adjustment, the upper punch and the friction in the mold phase, (2) improper granulation of the ingredients, such as too little slippery material, too thick powder.
(1) Adjusted separately
(2) Reprocessing the drug
5
Feeder damage
Battered with the undershoot
(1) The film is not properly adjusted, the lower punch is higher than the middle die plane, (2) the lower punching fixing screw is loose, and the lower punching rises out of the middle die plane.
When installing and adjusting the die, be sure to find that the screw is loose. Immediately tighten the die to the bottom of the die.
Battered under the middle mold
The middle mold fixing screw is loose, and the middle mold rises out of the plane of the middle mold platen.
Ibid.
Being hit by
(1) Reverse during adjustment, causing collision
(2) When the adjustment, the position of the upper punching rod is too low, and turning the handwheel causes a collision
Pay attention when adjusting
6
Difficult to unload
The upper punch, the lower punch or the middle die cannot be taken out in the hole
(1) The size of the die or the die hole size of the tablet press is unqualified, and the fit is too tight.
(2) rusting with the countertop
(1) Pay attention to the installation if you find that the fit is too tight
(2) Wipe the mating surface and apply a layer of oil film during installation. Do not remove the die to clean the mating surface for a long time, apply anti-rust oil, and keep it properly.
7
Overlapping piece
Two feedings into one piece
When the tablet is adjusted, the handwheel has not been ejected and the handwheel is reversed to cause the feeder to repeatedly feed, resulting in overlapping sheets.
Be careful not to reverse when adjusting. If you have repeatedly added the material but have not yet become a superimposed piece, you can slowly reverse the handwheel to lift the top of the tablet to remove the added material and pull out the tablets. If it has been pressed into an overlapping piece and the car is topped, it will be handled according to the top car (see Note 7 for use)
8
Jumping and fragmentation
When the pill is shot, it is too bouncing or broken
(1) The film is not properly adjusted, and the lower punch surface is lower than the middle mold plane. When the tablets come out, they are blocked and even crushed. (2) The middle mold fixing screw is loose, and the middle mold rises to block the film.
(1) See page 2, page 2
(2) Adjusting the tightening medium mold
9
Unedged piece and cracked piece
The tablet is scratched from the middle surface of the middle mold, and even the tablet is broken.
(1) The middle mold finish is unqualified or worn and scratches the circumferential surface of the tablet. At the same time, the tablet is cracked due to the unsmoothness of the film. (2) Miscibility of the granulation of the ingredients occurs, resulting in a burr or a crack.
(1) Replace the middle mold (Note: the middle mold can be turned over after one side wears, and the other side is used)
(2) Reprocessing the drug
10
Not only pills
There are pits or uncovering on the surface of the tablet.
(1) The surface of the punch is not only
(2) improper granulation of ingredients
(1) Repair punch
(2) Reprocessing the drug
11
Loose tablets
Pills are not enough, loose and brittle, layered, etc.
(1) insufficient pressure
(2) improper granulation of ingredients
(1) Adjust the pressure (see Article 4 on page 4)
(2) Reprocessing the drug
12
The film is unstable
The difference in weight is too large
(1) The undercut fastening screw is loose, and the lower punch is raised to feed the filling amount. (2) The butterfly screw is loose, the lower adjustment wheel rotates, the filling amount is changed, (3) the particle is tight and the size is uneven.
(1) Press the lower punch to the end and tighten the lower punch fixing screw
(2) Re-adjust and tighten
(3) Pay attention to the granulation of the ingredients, especially when crushing the pieces and crushing them.
If you want to know more small electric tablet press operating specifications Knowledge, please log in to our company or direct pharmaceutical technology department Consulting, our factory will provide you with more professional services! : :

We are a professional manufacturer and exporter in range of Sexual Stimulant which including Sex pill,sex capsule,sensual granules,sex energy tea,also sex coffee.

In past years,our products had exported to Kuwait,Mexico,USA,Norway,AU,Canada and so on.high quality products and fast delivery were appreciated by our clients.

Any interesting items,pls.do not hesitate to contact me.welcome ODM & OEM.thanks and welcome inquiry.

Each kind herbal sex products for man and woman
Sex pill,Sex stimulant,sex energy drink,sensual stimulant
Chengdu Jingke Trading Co., Ltd. , https://www.jkherb.com

Serial number	Refueling part	Lubricating oil	Number of refueling per shift
1	Spindle hole oil cup (2 pieces)	butter	2-3 times
2	Eccentric wheel shell oil cup 1	butter	2-3 times
3	1 bridge axle oil cup	butter	2-3 times
4	Lifting the cam groove (ie the groove inside the large gear)	butter	Every week, check the surface of the groove to wipe off the dirt and add butter once.
5	Filling the groove of the cam	butter	Every shift inspection, depending on the situation
6	Gear tooth surface	butter	Every shift inspection, depending on the situation
7	Oil hole on connecting rod	Motor oil	1 time
8	Swing pivot point of the lever	Motor oil	1 time
9	Upper punching rod surface	Motor oil	2 times
10	Lifting rod surface	Motor oil	2 times

Serial number	category	Fault conditions	The cause of the failure	Failure prevention and treatment
1	Top car	After rushing into the middle mold, "top dead", the machine stops running	(1) The pressure is too large; the tablets are too hard (2) repeated feeding (3) The eccentric wheel shell and the spindle hole lack oil, the rotation resistance is too large, and even the phenomenon of â€œbite deathâ€ occurs due to severe wear. (4) The belt is too loose (5) Improper starting position (6) The hand is not strong enough	(1) Adjust the pressure gradually. Do not adjust too much at one time, and the tablets can't be pressed too hard. (2) Avoid repeated feeding. See No. 7 (3). Always keep lubricating. If it has been seriously worn or â€œkilledâ€, it must be disassembled and repaired immediately. (4) Adjust the belt, see the precautions for use, Article 3, (5) See the precautions for use, Article 6. (6) When the hand presser is pressed or the upper punch passes the low point of Zui, it must be more forceful. (7) For the disposal method after the top car, see Article 7 of the precautions for use.
2	Not working well	Generally not working properly	The friction surface of the moving parts lacks oil, enters dirt, rusts, and seriously wears out the parts.	Always check each part to keep it clean and lubricated (see lubrication maintenance section 1). If there is any bad condition, repair it immediately, and do not deteriorate or damage the machine.
2	Not working well	Heavy or blocked when the undershoot rises	(1) Since the surface of the die is not light or worn; or due to improper granulation of the ingredients, the powder adheres to the surface of the punch and the middle mold, which increases the resistance of the sheet. (2) The lifting cam is seriously worn or enters the sundries (3) improperly adjusted, so that the lower punching rod rises and the middle mold is ground.	(1) If the die is found to have a sticking phenomenon, replace the die or reprocess the drug according to the situation. (2) Check and repair, keep it clean and lubricated. (3) Pay attention to adjustments
3	vibration	Abnormal vibration	(1) Loose parts and screws (2) The parts are seriously worn (3) The friction surface is dry or lacks oil or enters the dirt	(1) Regular inspection, see section 2 of lubrication maintenance, (2) frequent inspections, timely repair of worn parts. (3) Always pay attention to the cleaning and lubrication of each friction surface, especially pay attention to the direct view, but the working load is the important friction surface of the main shaft and the eccentric.
4	Wear	The friction surface of the main shaft and the hole is quickly worn or even burned out.	Lack of oil, enter impurities	Always keep clean and lubricated, the lubricant used must be clean and free of impurities
		Rapid wear and tear on the bridge axle and sleeve	Ibid.	Ibid.
		Upper punching rod and sleeve wear and wear quickly	Ibid.	Ibid.
		Lifting cam groove wears quickly	In addition to the above reasons, there are: (1) improper granulation of the ingredients, or the surface of the die is not light, the sticking phenomenon occurs, the sheet resistance is increased and the load of the cam groove is increased, and the wear is rapidly worn. (2) The lifting roller is turned too tight or rusted. Do not move.	(1) Check the die. If there is a sticking phenomenon, replace the die or re-dosing and granulating according to the situation. (2) Remove and repair
		Die surface wears quickly	(1) Improper adjustment, the upper punch and the friction in the mold phase, (2) improper granulation of the ingredients, such as too little slippery material, too thick powder.	(1) Adjusted separately (2) Reprocessing the drug
5	Feeder damage	Battered with the undershoot	(1) The film is not properly adjusted, the lower punch is higher than the middle die plane, (2) the lower punching fixing screw is loose, and the lower punching rises out of the middle die plane.	When installing and adjusting the die, be sure to find that the screw is loose. Immediately tighten the die to the bottom of the die.
		Battered under the middle mold	The middle mold fixing screw is loose, and the middle mold rises out of the plane of the middle mold platen.	Ibid.
		Being hit by	(1) Reverse during adjustment, causing collision (2) When the adjustment, the position of the upper punching rod is too low, and turning the handwheel causes a collision	Pay attention when adjusting
6	Difficult to unload	The upper punch, the lower punch or the middle die cannot be taken out in the hole	(1) The size of the die or the die hole size of the tablet press is unqualified, and the fit is too tight. (2) rusting with the countertop	(1) Pay attention to the installation if you find that the fit is too tight (2) Wipe the mating surface and apply a layer of oil film during installation. Do not remove the die to clean the mating surface for a long time, apply anti-rust oil, and keep it properly.
7	Overlapping piece	Two feedings into one piece	When the tablet is adjusted, the handwheel has not been ejected and the handwheel is reversed to cause the feeder to repeatedly feed, resulting in overlapping sheets.	Be careful not to reverse when adjusting. If you have repeatedly added the material but have not yet become a superimposed piece, you can slowly reverse the handwheel to lift the top of the tablet to remove the added material and pull out the tablets. If it has been pressed into an overlapping piece and the car is topped, it will be handled according to the top car (see Note 7 for use)
8	Jumping and fragmentation	When the pill is shot, it is too bouncing or broken	(1) The film is not properly adjusted, and the lower punch surface is lower than the middle mold plane. When the tablets come out, they are blocked and even crushed. (2) The middle mold fixing screw is loose, and the middle mold rises to block the film.	(1) See page 2, page 2 (2) Adjusting the tightening medium mold
9	Unedged piece and cracked piece	The tablet is scratched from the middle surface of the middle mold, and even the tablet is broken.	(1) The middle mold finish is unqualified or worn and scratches the circumferential surface of the tablet. At the same time, the tablet is cracked due to the unsmoothness of the film. (2) Miscibility of the granulation of the ingredients occurs, resulting in a burr or a crack.	(1) Replace the middle mold (Note: the middle mold can be turned over after one side wears, and the other side is used) (2) Reprocessing the drug
10	Not only pills	There are pits or uncovering on the surface of the tablet.	(1) The surface of the punch is not only (2) improper granulation of ingredients	(1) Repair punch (2) Reprocessing the drug
11	Loose tablets	Pills are not enough, loose and brittle, layered, etc.	(1) insufficient pressure (2) improper granulation of ingredients	(1) Adjust the pressure (see Article 4 on page 4) (2) Reprocessing the drug
12	The film is unstable	The difference in weight is too large	(1) The undercut fastening screw is loose, and the lower punch is raised to feed the filling amount. (2) The butterfly screw is loose, the lower adjustment wheel rotates, the filling amount is changed, (3) the particle is tight and the size is uneven.	(1) Press the lower punch to the end and tighten the lower punch fixing screw (2) Re-adjust and tighten (3) Pay attention to the granulation of the ingredients, especially when crushing the pieces and crushing them.